Post by Homeschool†Shopper on Feb 3, 2005 19:08:48 GMT -5
How To Color Fireplace Flames
If you enjoy sitting around your fireplace and watching colorful flames dance, you'll be happy to know you can color your own flames quite cheaply. Basically, there are three methods of coloring fireplace flames. You can soak the logs in an alcohol solution which contains certain chemicals. Or you can soak the logs in a water solution containing certain chemicals and then dry them. And finally, you can just throw certain chemicals into the flames. The various chemicals or salts required for certain colors of flames are as follows:
·3 parts Potassium sulphate (Chromealum) and 1 part potassium nitrate (Salt Peter) for violet flames
·Strontium chloride for red flames
·Calcium chloride (bleaching powder) for blue flames
·Magnesium sulphate (Epson Salts) for white flames
·Baronsalts (Borax) for yellowish-green flames
·Copper sulphate (blue vitrol/Bluestone) for green flames
·Sodium chloride (table salt) for yellow flames Colorful flames: 1/2 lb. baking soda to 1/2 gallon of water, or 1/2 lb. borax to 1/2 gallon of water, or 1/2 lb. salt to 1/2 gallon of water. Soak pinecones overnight and put in mesh bag to dry You may also treat pinecones, coarse sawdust or cork waste and throw them into the fireplace to color the fire.
They are far easier to treat and take less time to dry. Here are two methods for treating bases such as course sawdust, pinecones and cork waste. Best for sawdust - Dissolve the chemical in water. Stir in your base. When the solution is completely absorbed, spread the base out in a thin layer to dry.
Best for cork-based chips - Add 1 pint of liquid glue to 7 parts of water. Crush the chemical to a fine powder and add 1 pound of the powder to each gallon of glue-water. Put into the liquid as much of the sawdust, cork waste or pinecones that it will take, stirring and adding more base until all the liquid has been absorbed.
Spread out on a rack to dry. It is better to treat separate portions of your base with the solution of a single chemical than to treat the base in a single mixture of various chemicals.
After drying the separately treated portions of sawdust or cork waste, you can then mix them together in order to achieve distinctly colored flames. There is no fixed proportion of chemicals to be used to a given amount of water. As much of the powdered chemical should be mixed with water as will dissolve, until you have a saturated solution.
The only exception is ordinary table salt (sodium chloride), in which case you should use 1/2 ounce of salt to each pint of water. Coarse hardwood sawdust is better than pine or other softwood sawdust as a base.
Cork waste also makes an excellent base.Materials & Supplies:
Most of the ingredients needed for this project can be found at your local grocery store. The not-so-common ingredients / chemicals, such as copper sulfate and calcium chloride, can be found online at the Chemistry Store.
Young Living Independent
Distributor #737932
Stacy
If you enjoy sitting around your fireplace and watching colorful flames dance, you'll be happy to know you can color your own flames quite cheaply. Basically, there are three methods of coloring fireplace flames. You can soak the logs in an alcohol solution which contains certain chemicals. Or you can soak the logs in a water solution containing certain chemicals and then dry them. And finally, you can just throw certain chemicals into the flames. The various chemicals or salts required for certain colors of flames are as follows:
·3 parts Potassium sulphate (Chromealum) and 1 part potassium nitrate (Salt Peter) for violet flames
·Strontium chloride for red flames
·Calcium chloride (bleaching powder) for blue flames
·Magnesium sulphate (Epson Salts) for white flames
·Baronsalts (Borax) for yellowish-green flames
·Copper sulphate (blue vitrol/Bluestone) for green flames
·Sodium chloride (table salt) for yellow flames Colorful flames: 1/2 lb. baking soda to 1/2 gallon of water, or 1/2 lb. borax to 1/2 gallon of water, or 1/2 lb. salt to 1/2 gallon of water. Soak pinecones overnight and put in mesh bag to dry You may also treat pinecones, coarse sawdust or cork waste and throw them into the fireplace to color the fire.
They are far easier to treat and take less time to dry. Here are two methods for treating bases such as course sawdust, pinecones and cork waste. Best for sawdust - Dissolve the chemical in water. Stir in your base. When the solution is completely absorbed, spread the base out in a thin layer to dry.
Best for cork-based chips - Add 1 pint of liquid glue to 7 parts of water. Crush the chemical to a fine powder and add 1 pound of the powder to each gallon of glue-water. Put into the liquid as much of the sawdust, cork waste or pinecones that it will take, stirring and adding more base until all the liquid has been absorbed.
Spread out on a rack to dry. It is better to treat separate portions of your base with the solution of a single chemical than to treat the base in a single mixture of various chemicals.
After drying the separately treated portions of sawdust or cork waste, you can then mix them together in order to achieve distinctly colored flames. There is no fixed proportion of chemicals to be used to a given amount of water. As much of the powdered chemical should be mixed with water as will dissolve, until you have a saturated solution.
The only exception is ordinary table salt (sodium chloride), in which case you should use 1/2 ounce of salt to each pint of water. Coarse hardwood sawdust is better than pine or other softwood sawdust as a base.
Cork waste also makes an excellent base.Materials & Supplies:
Most of the ingredients needed for this project can be found at your local grocery store. The not-so-common ingredients / chemicals, such as copper sulfate and calcium chloride, can be found online at the Chemistry Store.
Young Living Independent
Distributor #737932
Stacy